PANASONIC TX-32LZD80-TX-37LZD80 SERVICE MODE AND LED BLINKING CODE

PANASONIC TX-32LZD80 -TX-37LZD80 

SERVICE MODE AND LED BLINKING CODE 

Self Check
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep
pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check,
switch off the TV set at the power button.
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
Power LED blinking timing chart
1. Subject
Information of LED Flashing timing chart.
2. Contents
When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the
defective block can be identified by number of blinking of the Power LED on the front panel of the unit.

Service Mode Function
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can
be adjusted by remote control in Service Menu
How to enter SERVICE
While pressing (-/v) button on the TV unit, press “0” on the remote control for 3 times within 2 seconds.
Note: To exit from Service mode, press the exit button on remote control.
Key Command
• Press the 3/4 button to change the adjustment values or function.
• Press the 1/2 button to step up/down through the functions and adjustments
• Press the numerical button VOLUME (+/-) to change of each option item.
• Press the OK button after each adjustment has been made to store the required values.
Setting Inspection
Voltage Confirmation
P board
Description
Test point
Position
Normal mode
Stand by mode
Active stand by mode
Sound_Vcc
TP7050
P7, pin 1,2
18V +/- 1V
Max 3V
Max 3V
BT_30V
TP7060
P7, pin 5
31V +/- 1V
Max 3V
31V +/- 1V
SUB_5V
TP7059
P7, pin 12,13,14
5,1V +/- 0,2V
Max 1V
5,1V +/- 0,2V
SUB_9V
TP7055

9,1V +/- 0,3V
Max 1V
9,1V +/- 0,3V
DTV_12V
TP7057
P7, pin 17
12V +/- 0,4V
Max 1V
12V +/- 0,4V
PANEL_12V
TP7058
P7, pin 20,21
12V +/- 0,4V
Max 2V
Max 2V
5VS
TP7061
P7, pin 22,23
5V +/- 0,2V
5V +/- 0,2V
5V +/- 0,2V
STB_5V
TP7062
P6, pin 11
5V +/- 0,2V
5V +/- 0,2V
5V +/- 0,2V
SUB_6V
TP7064
P6, pin 13
6,1V +/- 0,4V
Max 1V
6,1V +/- 0,4V
V+ - V-
TP7025-26
P6, pin 23
370V - 395V
Max 1V
370V - 395V
12V
TP7070
P5, pin 1,3
P2, pin 1
12V +/- 0,4V
Max 3V
12V +/- 0,4V

A board
5VS
TP1037
A1, pin 10
5V +/- 2%
DTV12V
TP1016
A7, pin 20,21
12V +/- 2%
SUB9V
TP1015
A7, pin 17
9V +/- 2%
SUB5V
TP1011
A7, pin 12,13,14
5V +/- 2%
BT30V
TP1010
A7, pin 5
30V +/- 2%
SUB6V
TP1014
A6, pin 23
6V +/- 2%
PNL12V
TP1012
A7, pin 22,23
12V +/- 2%
S_17V
TP1013
A7, pin 1,2
17 +/- 2%